@@ -28,7 +28,6 @@ Hardware Reference Boards
The following boards are supported by the meta-yocto-bsp layer:
* Texas Instruments Beaglebone (beaglebone-yocto)
- * Ubiquiti Networks EdgeRouter Lite (edgerouter)
* General IA platforms (genericx86 and genericx86-64)
For more information see the board's section below. The appropriate MACHINE
@@ -48,7 +47,6 @@ Consumer Devices
The following consumer devices are supported by the meta-yocto-bsp layer:
* Intel x86 based PCs and devices (genericx86)
- * Ubiquiti Networks EdgeRouter Lite (edgerouter)
For more information see the device's section below. The appropriate MACHINE
variable value corresponding to the device is given in brackets.
@@ -153,113 +151,3 @@ From a Linux system with access to the image files perform the following steps:
# dd if=core-image-minimal-beaglebone-yocto.wic of=/dev/sdb
3. Insert the SD card into the Beaglebone and boot the board.
-
-Ubiquiti Networks EdgeRouter Lite (edgerouter)
-==============================================
-
-The EdgeRouter Lite is part of the EdgeMax series. It is a MIPS64 router
-(based on the Cavium Octeon processor) with 512MB of RAM, which uses an
-internal USB pendrive for storage.
-
-Setup instructions
-------------------
-
-You will need the following:
-* RJ45 -> serial ("rollover") cable connected from your PC to the CONSOLE
- port on the device
-* Ethernet connected to the first ethernet port on the board
-
-If using NFS as part of the setup process, you will also need:
-* NFS root setup on your workstation
-* TFTP server installed on your workstation (if fetching the kernel from
- TFTP, see below).
-
---- Preparation ---
-
-Build an image (e.g. core-image-minimal) using "edgerouter" as the MACHINE.
-In the following instruction it is based on core-image-minimal. Another target
-may be similiar with it.
-
---- Booting from NFS root / kernel via TFTP ---
-
-Load the kernel, and boot the system as follows:
-
- 1. Get the kernel (vmlinux) file from the tmp/deploy/images/edgerouter
- directory, and make them available on your TFTP server.
-
- 2. Connect the board's first serial port to your workstation and then start up
- your favourite serial terminal so that you will be able to interact with
- the serial console. If you don't have a favourite, picocom is suggested:
-
- $ picocom /dev/ttyS0 -b 115200
-
- 3. Power up or reset the board and press a key on the terminal when prompted
- to get to the U-Boot command line
-
- 4. Set up the environment in U-Boot:
-
- => setenv ipaddr <board ip>
- => setenv serverip <tftp server ip>
-
- 5. Download the kernel and boot:
-
- => tftp $loadaddr vmlinux
- => bootoctlinux $loadaddr coremask=0x3 root=/dev/nfs rw nfsroot=<nfsroot ip>:<rootfs path> ip=<board ip>:<server ip>:<gateway ip>:<netmask>:edgerouter:eth0:off mtdparts=phys_mapped_flash:512k(boot0),512k(boot1),64k@3072k(eeprom)
-
---- Booting from USB disk ---
-
-To boot from the USB disk, you either need to remove it from the edgerouter
-box and populate it from another computer, or use a previously booted NFS
-image and populate from the edgerouter itself.
-
-Type 1: Use partitioned image
------------------------------
-
-Steps:
-
- 1. Remove the USB disk from the edgerouter and insert it into a computer
- that has access to your build artifacts.
-
- 2. Flash the image.
-
- # dd if=core-image-minimal-edgerouter.wic of=/dev/sdb
-
- 3. Insert USB disk into the edgerouter and boot it.
-
-Type 2: NFS
------------
-
-Note: If you place the kernel on the ext3 partition, you must re-create the
- ext3 filesystem, since the factory u-boot can only handle 128 byte inodes and
- cannot read the partition otherwise.
-
- These boot instructions assume that you have recreated the ext3 filesystem with
- 128 byte inodes, you have an updated uboot or you are running and image capable
- of making the filesystem on the board itself.
-
-
- 1. Boot from NFS root
-
- 2. Mount the USB disk partition 2 and then extract the contents of
- tmp/deploy/core-image-XXXX.tar.bz2 into it.
-
- Before starting, copy core-image-minimal-xxx.tar.bz2 and vmlinux into
- rootfs path on your workstation.
-
- and then,
-
- # mount /dev/sda2 /media/sda2
- # tar -xvjpf core-image-minimal-XXX.tar.bz2 -C /media/sda2
- # cp vmlinux /media/sda2/boot/vmlinux
- # umount /media/sda2
- # reboot
-
- 3. Reboot the board and press a key on the terminal when prompted to get to the U-Boot
- command line:
-
- # reboot
-
- 4. Load the kernel and boot:
-
- => ext2load usb 0:2 $loadaddr boot/vmlinux
- => bootoctlinux $loadaddr coremask=0x3 root=/dev/sda2 rw rootwait mtdparts=phys_mapped_flash:512k(boot0),512k(boot1),64k@3072k(eeprom)
deleted file mode 100644
@@ -1,26 +0,0 @@
-#@TYPE: Machine
-#@NAME: Edgerouter
-#@DESCRIPTION: Machine configuration for a generic edgerouter
-
-require conf/machine/include/mips/tune-mips64.inc
-
-MACHINE_FEATURES = "pci ext2 ext3 serial"
-
-KERNEL_IMAGETYPE = "vmlinux"
-KERNEL_ALT_IMAGETYPE = "vmlinux.bin"
-KERNEL_IMAGE_STRIP_EXTRA_SECTIONS = ".comment"
-
-PREFERRED_PROVIDER_virtual/kernel ?= "linux-yocto"
-PREFERRED_VERSION_linux-yocto ?= "6.1%"
-
-SERIAL_CONSOLES = "115200;ttyS0"
-USE_VT ?= "0"
-
-MACHINE_EXTRA_RRECOMMENDS = "kernel-modules"
-
-IMAGE_FSTYPES ?= "jffs2 tar.bz2 wic wic.bmap"
-JFFS2_ERASEBLOCK = "0x10000"
-
-WKS_FILE ?= "edgerouter.wks"
-IMAGE_BOOT_FILES ?= "vmlinux;vmlinux.64"
-do_image_wic[depends] += "mtools-native:do_populate_sysroot dosfstools-native:do_populate_sysroot"
deleted file mode 100644
@@ -1,89 +0,0 @@
-# Copyright (C) 2014 Intel Corporation
-#
-# Released under the MIT license (see COPYING.MIT)
-
-# This module adds support to testimage.bbclass to deploy images and run
-# tests on a Ubiquiti Networks EdgeRouter Lite. The device must be set up
-# to boot into the master image already - the easiest way to do that is as
-# follows:
-#
-# 1. Take out the internal USB drive and plug it into your PC
-# 2. Repartition the USB drive so that you have three partitions in this
-# order:
-# 1: vfat, labelled "boot" (it will need to be formatted with mkfs.vfat
-# for this to be possible, since FAT partitions formatted under
-# DOS/Windows will only support uppercase labels)
-# 2: ext3 (for master image) labelled "testmaster"
-# 3: ext3 (for image under test) labelled "testrootfs"
-# 3. Copy the kernel to be used by the master image to the FAT partition
-# (it should be named "vmlinux.64" with the factory u-boot configuration)
-# 4. Install the master image onto the "testmaster" ext3 partition. If
-# you do this by just extracting the contents of an image onto the
-# partition, you will also likely need to create the master image marker
-# file /etc/masterimage within this partition so that we can tell when
-# we're booted into it that it is the master image.
-# 5. Put the USB drive back into the device, and ensure the console port
-# and first ethernet port are connected before powering on
-#
-# TEST_SERIALCONTROL_CMD will need to be set in local.conf so that we can
-# interact with u-boot over the serial console port.
-
-import os
-import bb
-import time
-import subprocess
-import sys
-import pexpect
-
-from oeqa.controllers.controllerimage import ControllerImageHardwareTarget
-
-
-class EdgeRouterTarget(ControllerImageHardwareTarget):
-
- def __init__(self, d):
- super(EdgeRouterTarget, self).__init__(d)
-
- self.image_fstype = self.get_image_fstype(d)
- self.deploy_cmds = [
- 'mount -L boot /boot',
- 'mkdir -p /mnt/testrootfs',
- 'mount -L testrootfs /mnt/testrootfs',
- 'cp ~/test-kernel /boot',
- 'rm -rf /mnt/testrootfs/*',
- 'tar xvf ~/test-rootfs.%s -C /mnt/testrootfs' % self.image_fstype
- ]
- if not self.serialcontrol_cmd:
- bb.fatal("This TEST_TARGET needs a TEST_SERIALCONTROL_CMD defined in local.conf.")
-
-
- def _deploy(self):
- self.controller.run("umount /mnt/testrootfs;")
- self.controller.ignore_status = False
- self.controller.copy_to(self.kernel, "~/test-kernel")
- self.controller.copy_to(self.rootfs, "~/test-rootfs.%s" % self.image_fstype)
- for cmd in self.deploy_cmds:
- self.controller.run(cmd)
-
- def _start(self, params=None):
- self.power_cycle(self.controller)
- try:
- serialconn = pexpect.spawn(self.serialcontrol_cmd, env=self.origenv, logfile=sys.stdout)
- serialconn.expect("U-Boot")
- serialconn.sendline("a")
- serialconn.expect("Octeon ubnt_e100#")
- serialconn.sendline("fatload usb 0:1 $loadaddr test-kernel")
- serialconn.expect(" bytes read")
- serialconn.expect("Octeon ubnt_e100#")
- serialconn.sendline("bootoctlinux $loadaddr coremask=0x3 root=/dev/sda3 rw rootwait mtdparts=phys_mapped_flash:512k(boot0),512k(boot1),64k@3072k(eeprom)")
- serialconn.expect("login:", timeout=120)
- serialconn.close()
- except pexpect.ExceptionPexpect as e:
- bb.fatal('Serial interaction failed: %s' % str(e))
-
- def _wait_until_booted(self):
- try:
- serialconn = pexpect.spawn(self.serialcontrol_cmd, env=self.origenv, logfile=sys.stdout)
- serialconn.expect("login:", timeout=120)
- serialconn.close()
- except pexpect.ExceptionPexpect as e:
- bb.fatal('Serial interaction failed: %s' % str(e))
@@ -1,6 +1,5 @@
KBRANCH:genericx86 = "standard/base"
KBRANCH:genericx86-64 = "standard/base"
-KBRANCH:edgerouter = "standard/edgerouter"
KBRANCH:beaglebone-yocto = "standard/beaglebone"
KMACHINE:genericx86 ?= "common-pc"
@@ -9,5 +8,4 @@ KMACHINE:beaglebone-yocto ?= "beaglebone"
COMPATIBLE_MACHINE:genericx86 = "genericx86"
COMPATIBLE_MACHINE:genericx86-64 = "genericx86-64"
-COMPATIBLE_MACHINE:edgerouter = "edgerouter"
COMPATIBLE_MACHINE:beaglebone-yocto = "beaglebone-yocto"
@@ -1,6 +1,5 @@
KBRANCH:genericx86 = "v5.15/standard/base"
KBRANCH:genericx86-64 = "v5.15/standard/base"
-KBRANCH:edgerouter = "v5.15/standard/edgerouter"
KBRANCH:beaglebone-yocto = "v5.15/standard/beaglebone"
KMACHINE:genericx86 ?= "common-pc"
@@ -9,15 +8,12 @@ KMACHINE:beaglebone-yocto ?= "beaglebone"
SRCREV_machine:genericx86 ?= "024d08fb706170a9723e9751e505681f9d4c7ab6"
SRCREV_machine:genericx86-64 ?= "024d08fb706170a9723e9751e505681f9d4c7ab6"
-SRCREV_machine:edgerouter ?= "2ac6461adfceb54f47a756046fbdd142adce4301"
SRCREV_machine:beaglebone-yocto ?= "26aee42556a000123129552b73de6bf2ac039034"
COMPATIBLE_MACHINE:genericx86 = "genericx86"
COMPATIBLE_MACHINE:genericx86-64 = "genericx86-64"
-COMPATIBLE_MACHINE:edgerouter = "edgerouter"
COMPATIBLE_MACHINE:beaglebone-yocto = "beaglebone-yocto"
LINUX_VERSION:genericx86 = "5.15.103"
LINUX_VERSION:genericx86-64 = "5.15.103"
-LINUX_VERSION:edgerouter = "5.15.103"
LINUX_VERSION:beaglebone-yocto = "5.15.103"
@@ -1,6 +1,5 @@
KBRANCH:genericx86 = "v6.1/standard/base"
KBRANCH:genericx86-64 = "v6.1/standard/base"
-KBRANCH:edgerouter = "v6.1/standard/edgerouter"
KBRANCH:beaglebone-yocto = "v6.1/standard/beaglebone"
KMACHINE:genericx86 ?= "common-pc"
@@ -9,15 +8,12 @@ KMACHINE:beaglebone-yocto ?= "beaglebone"
SRCREV_machine:genericx86 ?= "423e1996694b61fbfc8ec3bf062fc6461d64fde1"
SRCREV_machine:genericx86-64 ?= "423e1996694b61fbfc8ec3bf062fc6461d64fde1"
-SRCREV_machine:edgerouter ?= "423e1996694b61fbfc8ec3bf062fc6461d64fde1"
SRCREV_machine:beaglebone-yocto ?= "423e1996694b61fbfc8ec3bf062fc6461d64fde1"
COMPATIBLE_MACHINE:genericx86 = "genericx86"
COMPATIBLE_MACHINE:genericx86-64 = "genericx86-64"
-COMPATIBLE_MACHINE:edgerouter = "edgerouter"
COMPATIBLE_MACHINE:beaglebone-yocto = "beaglebone-yocto"
LINUX_VERSION:genericx86 = "6.1.20"
LINUX_VERSION:genericx86-64 = "6.1.20"
-LINUX_VERSION:edgerouter = "6.1.20"
LINUX_VERSION:beaglebone-yocto = "6.1.20"
deleted file mode 100644
@@ -1,4 +0,0 @@
-# short-description: Create SD card image for Edgerouter
-# long-description: Create a partitioned SD card image for MIPS64 Edgerouter reference hardware.
-part /boot --source bootimg-partition --ondisk sda --fstype=vfat --label boot --active --align 4 --size 16
-part / --source rootfs --ondisk sda --fstype=ext4 --label root --align 4